Collecting specimens is only half of sampling; the other half is getting them to the laboratory bench unchanged, tested under the right protocol, and reported in a form buyers can act on. Part 2 of this series traces that journey: sealing and identification at the factory, transport and storage discipline, laboratory intake checks, the sequence from screening to confirmatory analysis, and the reading of the final report. Each handoff carries simple controls that keep the evidence chain intact. Get the flow right and one sampling round produces verdicts every downstream party can trust.
Key takeawaysRepresentative results depend on sealed, identified specimens drawn from finished production, not on laboratory technique alone. · Acceptance sampling theory explains why random selection and defined sample sizes underpin every credible sampling plan. [1] · Factory acceptance logic shows why testing against agreed criteria before release protects both buyer and supplier. [2] · Simulant, temperature, duration, and replicate choices must be confirmed with the laboratory before sampling, since they cannot be corrected afterward. · Reading the report means checking the protocol reference first, then comparing each result with the correct limit type.
Part 1 of this series covered which lots to sample and how many specimens each protocol needs. Part 2 follows the specimens after they leave the factory: sealing, identification, transport, laboratory intake, the test sequence itself, and the interpretation of what comes back. This middle stretch is where many test programs quietly fail, not because the laboratory erred but because the specimens that arrived no longer represented the lot.
The chain from factory to bench has no single owner by default. The sampler seals, a courier carries, the laboratory logs in, and each handoff is a chance for mix-ups, damage, or delay. Buyers who define each handoff in advance, with names, records, and photographs, get results they can defend. Buyers who leave it informal get numbers attached to uncertain origins.
This article walks the full flow in order, with the practical controls that keep specimens representative and reports readable at each step.
Sealing and identification at the factory
Sealing is the moment sampling becomes evidence. Each specimen set goes into a clean, dry container or bag that is then sealed with a tamper-evident method and marked with a unique identifier, the product description, the lot or batch number, the sampling date, and the sampler's name. Spare sets for retest get their own seals and identifiers rather than sharing a bag, so a retest never depends on reopening the primary set.
Identification must survive the courier. Labels go on the parcel and inside it, because outer labels get torn; the inner slip repeats the identifier, the contents, and the destination laboratory. Photographs taken at sealing time show the specimens, the sealed parcels, and the shipping labels in one record, which later resolves the common dispute about whether the laboratory received what the factory sent.
The sampling record itself is short but non-negotiable: where the specimens came from within the lot, how they were selected, how many were taken and why, who witnessed the process, and what environmental conditions applied. This record is what lets a buyer commission independent food contact material testing independent food contact material testing on a defined lot and later show exactly which goods the results describe. Without it, even a perfect laboratory result floats unattached to any shipment.
Transport, storage, and laboratory intake
Specimens travel better than most people assume, except when they do not. Heat-sensitive materials should avoid hot vehicles and long warehouse waits, fragile articles need rigid outer packing, and anything with printed or coated food-contact surfaces should be separated so faces do not abrade each other. The courier booking should specify delivery timing that respects any laboratory stability window, particularly for overall migration work where delayed testing can complicate interpretation.
On arrival, a competent laboratory logs the parcel condition, the seal numbers, the identifiers, and the accompanying request before opening anything. Discrepancies such as broken seals, mismatched identifiers, or missing request details should trigger a hold and a query back to the sender, not silent testing of uncertain material. Buyers can help by sending the sampling record ahead of the parcel so intake staff know what to expect.
The statistical reasoning behind all of this predates modern food-contact rules. Acceptance sampling theory describes how randomly drawn specimens support inferences about a larger lot and why sample sizes follow from risk decisions rather than habit, and a general overview of that theory explains the operating-characteristic logic behind the tables laboratories and inspectors use. [1] Keeping the selection random and the identification intact is what makes that theory applicable to your shipment.
From screening to confirmatory analysis
| Step | What happens | Buyer control point |
|---|---|---|
| Intake verification | Laboratory checks seals, identifiers, and request details | Send sampling record ahead; require discrepancy queries |
| Preparation | Specimens cleaned and conditioned per protocol | Confirm conditioning does not alter the food-contact surface |
| Screening | Initial runs identify migration levels and suspect substances | Agree screening scope covers all ordered materials |
| Confirmatory work | Replicates and specific methods quantify regulated substances | Confirm replicate count and limit references |
| Review | Results checked against protocol and limit tables | Require protocol citation on every reported result |
| Reporting | Signed report with method references and conditions | File report with sampling record and lot documents |
Reading the report without missteps
Start with the protocol block, not the numbers. Confirm the simulant, temperature, contact duration, number of replicates, and the standard or regulation cited, then check that these match the order. A result produced under the wrong condition is not a borderline pass; it is simply not the ordered test, and acting on it risks both false confidence and false alarms.
Then map each result to its limit type. Some limits apply to each individual test, others to the behavior across repeated exposures, and compositional limits apply to the material rather than the migrate. The report should state the applicable limit alongside each finding, but buyers should still verify against the regulation rather than trusting a summary sentence. When limits differ between markets, file each verdict against its own rule instead of blending them.
The broader logic mirrors factory acceptance practice in equipment industries, where testing against agreed criteria before release protects both sides of a transaction, and the general concept of factory acceptance testing illustrates why pre-release verification beats post-delivery dispute. [2] Treat the laboratory report the same way: evidence for a release decision, read carefully before the goods move, not decoration for a file nobody opens.
One sampling round serves every downstream need only when the specimens are sealed, identified, transported, and reported as a single traceable chain. Break any link and the whole round has to be repeated.
Sources
- Wikipedia: Acceptance sampling —— Overview of acceptance sampling including AQL concepts used in product inspection.
- Wikipedia: Factory acceptance test —— Overview of factory acceptance testing performed before shipment or installation.
Frequently asked questions
What sampling records should accompany specimens to the laboratory?
Sealed specimens taken from finished production, with the lot identity, sampling date, sampler identity, and quantity recorded and countersigned where possible. Photographs of the sampling point, the sealed parcels, and the shipping labels complete the file. Without this record, a laboratory cannot confirm that its results describe your shipment rather than some other lot.
Why does transport and storage of specimens matter so much?
Because a result describes the specimen, and only a representative, well-preserved specimen describes the lot. Heat, sunlight, delay, or substitution on the way to the laboratory can each shift results or break traceability. Chain-of-custody discipline is what converts a laboratory number into evidence you can act on and show to customers.
How do I read a migration test report without misinterpreting it?
First check the protocol reference on the report: simulant, temperature, duration, and number of replicates must match what was ordered. Then compare each result with the applicable limit, noting that some limits apply per test while others apply across repeated exposures. If anything looks inconsistent, ask the laboratory for clarification before sharing the report, since a misread number can trigger an unnecessary reformulation.
Can laboratory sampling be combined with a routine inspection visit?
Yes, and this is where combination saves real money. The inspector performing the commercial check can collect and seal laboratory specimens at the same time, provided both sides agree the specimens come from finished production. That avoids a second factory visit purely for sampling and keeps the commercial and laboratory evidence anchored to the same lot.